![]() ![]() It is made from conversion varnish and nitrocellulose lacquer, resulting in an easy-to-spray, fast-drying finish with the durability and toughness of varnish. However, it is more expensive and lacks some of the clarity of standard lacquer.Ĭatalyzed lacquer is a so-called “ conversion finish“. CAB lacquer is an ideal finish for light-colored woods because it preserves the light color. It also has slightly better heat resistance and is less brittle. This finish has the same general properties of nitrocellulose lacquer, except it is much whiter and yellows less over time. It is sometimes labeled as CAB-acrylic lacquer. For these reasons, it is not the best choice for a kitchen table finish, especially one made from a light-colored wood and exposed to lots of direct sunlight (unless you like the yellow look).ĬAB lacquer is typically made from a mixture of a cellulose resin called cellulose acetate butyrate (CAB) and acrylic. However, it yellows badly with age and only provides moderate resistance to water, heat, abrasion, and certain solvents such as alcohol. Originally developed as a substitute for shellac, NC lacquer is attractive, sprays like a dream, and rubs out better than most other finishes. If the label on the can just says lacquer, it’s almost certainly nitrocellulose lacquer. Here are the main types of lacquer that are used for wood finishing: The amounts and types of these materials produce lacquers with varying degrees of flexibility, color, and resistance to water, acids, alkalis, solvents, and heat. Lacquer is made from cellulose derived from cotton or wood fibers that is combined with a plasticizer, a resin, and a blend of solvents and diluents. Professionals especially appreciate lacquer’s fast drying time - 3 to 4 coats in one day is easily achieved. It dries fast, has decent protective qualities, provides excellent clarity and depth, rubs out well, and is fairly easy to repair. Deezer Playlist Tags Accessories Album Alfie All the Things You Are Amps Arpegio Autumn leaves Biography Black Nile Blues Blues for Yna Yna Brazil Cantaloupe Island Chitlins Con Carne Chords Classic Concerts/Events Effects Electrics/Physics Flamenco Four Fun Funk Funk in a deep freeze Gears Guitar/Archtop.Lacquer is a synthetic finish that has been the finish of choice in the furniture making industry since the 1920’s. For more information on buffing and polishing, click here. Wet sand with 800-grit and finer sanding papers, then buff to a high-gloss using sanding papers, polishes, and buffers. Or colored with ColorTone Liquid PigmentsĤ-10 coats (4-8 for thin “vintage” finish) Tinted with ColorTone Concentrated Liquid Stains ColorTone Aerosol Guitar Lacquerīehlen Nitrocellulose Stringed Instrument Lacquerįill wood. Washcoats are very thin coats using thinned finish. If you do get a run or sag, simply let the finish harden (24-hours) and level sand the blemish using 400-grit sandpaper and a backing block. Be careful when applying wet-coats, as it’s easy to create a run or sag on edges, or while trying to apply finish into the tighter areas of an instrument. The first coat should be a light, misting coat to the instrument - often referred to as a “tack-coat.” After 45-minutes or so, apply another, more deliberate “wet-coat.” Future coats should be wet, and be sure to give 1-2 hours between coats to allow the solvents to rise out of the finish. As you gain experience, you’ll find that fewer coats are required. Beginners should spray 10-12 coats to avoid sanding or buffing through the finish. ![]() The total number will depend upon how thick your coats are, how much sanding you do, and what your final desired film thickness is. Nitrocellulose finishes should have a total 6-12 coats - sealer, color, and clear coats combined. It’s ready to spray with no thinning required, for faster finish build-up in multiple coats. The finish has better resistance to cold-checking and scuffs. Stringed Instrument Lacquer produces a hard, durable finish that’s less brittle and more flexible than standard furniture lacquer, to accommodate the expansion and contraction of wooden instruments. The look, feel, and tone of nitrocellulose is hard to surpass, and it is easier than many finishes to repair or touch-up. It’s relatively easy to apply and buff to a beautiful, high gloss finish. Nitrocellulose lacquer is synonymous with well-crafted, vintage and modern instruments. Standard process for finishing an instrument with nitrocellullose lacquer
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |